意大利DUPLOMATIC迪普馬軸向柱塞變量泵
VPPL-070PCR-R00S/20N VPPL-100PCR-R00S/20N VPPL-008PQC-R00S/20N
VPPL-016PQC-R00S/20N VPPL-022PQC-R00S/20N VPPL-036PQC-R00S/20N
VPPL-046PQC-R00S/20N VPPL-070PQC-R00S/20N VPPL-100PQC-R00S/20N
VPPL-008PC5-R10S/20N VPPL-016PC5-R10S/20N VPPL-100PQC-R00B/20N
VPPL-022PC5-R10S/20N VPPL-036PC5-R10S/20N VPPL-046PC5-R10S/20N
VPPL-070PC6-R10S/20N VPPL-100PC6-R10S/20N VPPL-008PCR-R10S/20N
液壓泵自吸高度不超過500mm(或進口真空度不超過0.03MPa),若采用補油泵供油,供油壓力不得超過0.5MPa,當供油壓力超過0.5MPa時,要改用耐壓密封圈。對于柱塞泵,應盡量采用倒灌自吸方式。液壓泵裝機前應檢查安裝孔的深度是否大于泵的軸伸長度,防止產生頂軸現象,否則將燒毀泵,液壓泵使用注意事項。
VPPL-016PCR-R10S/20N VPPL-022PCR-R10S/20N VPPL-036PCR-R10S/20N
VPPL-046PCR-R10S/20N VPPL-070PCR-R10S/20N VPPL-100PCR-R10S/20N
VPPL-008PQC-R10S/20N VPPL-016PQC-R10S/20N VPPL-022PQC-R10S/20N
VPPL-036PQC-R10S/20N VPPL-046PQC-R10S/20N VPPL-070PQC-R10S/20N
VPPL-008PC5-R00B/20N VPPL-070PQC-R00B/20N VPPL-100PQC-R10S/20N
VPPL-016PC5-R00B/20N VPPL-022PC5-R00B/20N VPPL-036PC5-R00B/20N
VPPL-046PC5-R00B/20N VPPL-070PC6-R00B/20N VPPL-100PC6-R00B/20N
VPPL-008PCR-R00B/20N VPPL-016PCR-R00B/20N VPPL-022PCR-R00B/20N
液壓泵啟動時應先點動數次,油流方向和聲音都正常后,在低壓下運轉5~10min,然后投入正常運行。柱塞泵啟動前,必須通過殼上的泄油口向泵內灌滿清潔的工作油。 液壓泵的工作原理是什么呢?啟東高壓為您解答!廣東軸向液壓泵供應
意大利DUPLOMATIC迪普馬軸向柱塞變量泵