FFMmodel protection capacitorwith high voltage resistancein series being RC is comp osedofvoltage absorption device,itfitswellwith 35kv electric system.due to vacuum breaker(or other non-heavy switch),it produces the transition voltage to protect the product with high voltage from damaging,it is also used on other occasions with high voltage capacitor．
型號說明 model meanings
主要技術指標 main techniqueindessign
1. 電容偏差-5~+10%；
2. 損耗角正切值tan δ<0.05%；
3. 電介質的電容強度2.15μ，歷時1min；
4. 其余技術要求均按照《GB.T4704-32 高壓并聯電容器》。
1.Capacitance Deviation:-5~+10% ;
2.Tangent of Loss Angle tanδ<0.05% ;
3.Electrical Strenth of Dielectric Medium 2.1 5μ Last a period of time:1min;
4.The other technology requirementis accordingto" GB.T4704-32High Voltage Shunt Capacitor".
使用條件 servicecondition
1. 電容器安裝運行的海拔高度不超過1000m，環境空氣溫度為-40~+40℃。相對濕度不大于90%。
2. 安裝場所應無腐蝕氣體、蒸氣和導電性或爆炸性塵埃，并無劇烈的機械振動。
3. 電容器投入運行時，其端子上的剩余電壓不超過額定電壓的10%。
4. 過載荷
4.1 穩定過電壓
續運行電壓時1.00μn，并能在1.2μn，工頻過電壓下長期運行。
4.2 操作過電壓
電容器的承受不重擊穿開關所產生的1.5μn 的過渡過電壓( 峰值）。
4.3 穩態過電流
電容器能在1.5In 穩態過電流下運行，這個過電流是由于諧波及，容差和高至1.2In 的過電流共同作用的結果。
1.Height a bove sea level of capacitor’s installation and
shipping is not more than 1000m. Env ironmental air
temperature is-40 ℃ ~+40 ℃ Relative humidity is not more than 90% ;
2.There is no corruption gas,smoke,conductive or explosive dust,acute machine tremor in iastallation location no harmfuI gas or smoke.no conductive performance or acute tremor;
3.When cap a citors run,the spare voltage of its terminal is not more than10% of rated voltage;
4.Over Loading
4.1 Stabilization Voltage
Stabilization voltage can continuously run ac the Voltage of 1.00μn and can also lastingly run at the industrial frequency voltage of 1.2μn.
4.2 Operated Voltage
The bearing capacitor should not heav ily punch switch produced transition Voltage of 1.5μn(buzzing valuel).
4.3 Steady State Electricity
Capacitor can be operated underthe 1.5In steady current. Duetcits harmonious wave,the result of current caused the max difference and height of 1.2In together.
客戶訂做如有尺寸要求需提供以下數據 Size of customer requirements to be made if the following data
