上海嘉鵬科技有限公司綜合內外秀生化實驗設備制造經驗獨生產的DHL-B電腦恒流泵 ，進行系統詳解，可快速查詢產品的新報價、圖片、技術參數，或者進行產品性能比較，使用非常方便。先感謝您使用本廠的產品，請在使用本產品之前詳細閱讀本說明書。
1. DHL-B電腦恒流泵概述 ：
DHL-B電腦恒流泵是種新穎的電腦控制流量的蠕動泵，具有能自動選擇流量，地顯示輸液量，當輸液量達到預置總量時能自動報警并作相應的后處理等功能。該泵操作簡便，性能穩定、可靠，可長期連續工作，并能保存輸入的工作參數。適合需要蠕動泵的各行各業。
本蠕動泵可與本廠生產的DBS-100/160電腦全自動部份收集器配合工作。
2. DHL-B電腦恒流泵主要技術指標 ：
2.1 電源電壓：AC220V±10%，30Hz
2.2 使用環境：溫度0~40°C，濕度< 83%
2.3 流量選擇范圍：0.01ml/M~13.00ml/M
2.3.1 使用3mm硅膠管時：0.01ml/M~2.00ml/M（電腦自動限定）
2.3.2 使用3mm硅膠管時：0.3ml/M~13.00ml/M（電腦自動限定）
2.4 預置總量選擇范圍：0~9999ml或0~99.99 l。
2.5 百分比流量修正范圍：±30%（電腦自動限定）
2.6 具有數據斷電保存功能：可保存10年。
2.7 流量精度：±2%
3. DHL-B電腦恒流泵使用注意事項 ：
3.1 調距板（即泵頭前后的滑動板）的調節螺絲是用于調節液體壓力的，般只要擰到有液體流動即可，調節時須注意不要擰得太緊，否則滾子會擱死。
3.2儀器在使用期間，應隨時注意硅橡膠管是否完好，般在中速情況下運轉為佳，當發現硅橡膠管使用老化時，應及時更換。當儀器開始運轉時，硅橡膠管可能有向端腫起現象，可用手拉直即可。
3.3要注意保持泵槽內清潔，尤其對滾子軸套（當中只）必須擦干凈，以免“Ｔ”字輪擱死。如果長時間不使用，應取下硅橡膠管，延長使用期限。
3.4 DHL-B電腦恒流泵要注意妥善保管，存放在干燥、通風、無腐蝕氣體的地方。

 

上海嘉鵬科技有限公司 /
電話：      
400免費： 
手機： 
企業QQ，2880150292，2880150293，2880150290，2880150297
：
地址：上海市真陳路1398弄15號  郵編：200444

DHL-B series of constant-current pump computer
First of all, Thank you for using our products, please, before using this product read the manual.
1. Overview
DHL-B series of constant-current pump computer is a novel computer-controlled peristaltic pump flow has to flow automatically and accurately shows the volume of infusion, when the fluid reached automatically when the preset volume and a corresponding alarm post-processing functions. The pump is simple, stable performance, reliable, long-term continuous work and the work of preservation of input parameters. Peristaltic pump suitable for the needs of all walks of life.
The peristaltic pump can be factory produced DBS-100/160 computer with fully automatic traps most of the work.
2. The main technical indicators
2.1 supply voltage: AC220V ± 10%, 30Hz
2.2 environment: Temperature 0 ~ 40 ° C, humidity <83%
2.3 Flow selection: 0.01ml / M ~ 13.00ml / M
2.3.1 When using 3mm silicone tube: 0.01ml / M ~ 2.00ml / M (automatically qualify)
2.3.2 When using 3mm silicone tube: 0.3ml / M ~ 13.00ml / M (automatically qualify)
2.4 preset selection total: 0 ~ 9999ml or 0 ~ 99.99 l.
2.5 to amend the scope of the percentage of flow: ± 30% (the computer automatically qualify)
2.6 has a power saving data: can be stored for 10 years.
2.7 Flow accuracy: ± 2%

3. Caution
Plate 3.1 pitch (that is, before and after the pump head of the sliding board) is the adjustment screw for regulating the fluid pressure in general as long as the twist of the liquid can flow, regulation should be careful not to screw too tightly, or else will be tied up roller .
3.2 in the use of equipment, you should always pay attention to whether the silicone rubber tube intact, the general circumstances in the medium-speed running is better, when found in the use of an aging silicone rubber should be replaced promptly. When the equipment started to operate, the silicone rubber tube may have to end腫起phenomenon can be straightened by hand.
3.3 bed pump to keep clean, especially on the roller sleeve (of which a) must be clean so as not to "T" word round tied up. If the long period of time not to use, silicone rubber tube should be removed to extend the period of use.
3.4 Instrument to the attention of the proper custody, stored in dry, ventilated place without corrosive gas.