本公司6月7號08點50分報道：TCGB-19型電動土工布取樣器產品用途@企業動態
產品用途
YI、TCGB-19型電動土工布取樣器用途：
YI、TCGB-19型電動土工布取樣器用途：
TCGB-19型電動土工布取樣器其性能符合JTGE50公路土工合成材料試驗規程、SL235土工合成材料試驗規程、用手切取各種毛紡、混紡、化纖、針織等織物的圓形樣品。
Application of tcgb-19 electric geotextile Sampler:
The performance of tcgb-19 electric geotextile sampler conforms to jtge50 test specification for highway geosynthetics and sl235 test specification for geosynthetics. Round samples of wool, blended, chemical fiber and knitted fabrics are cut by hand.
技術參數
二、TCGB-19型電動土工布取樣器技術指標：
二、TCGB-19型電動土工布取樣器技術指標：
1、取樣面積：100cm2
2、可切厚度：15mm
3、外型尺寸：ф160X115mm
4、重量：1.5kg
Technical specifications of tcgb-19 electric geotextile Sampler:
1. Sampling area: 100cm2
2. Cutting thickness: 15mm
3. Dimensions: ф 160X115mm
4. Weight: 1.5kg
三、TCGB-19型電動土工布取樣器結構與調整：
1、切刀刀片為雙面刀片，具有四片，為圓外接四等分均布。刀片可以更換，具體操作為：松開件5十字螺釘（每片上有4顆螺釘），取下件6刀片壓板與件4取樣刀片，換上新的刀片，壓上件6刀片壓板，注意使刀片口為順時針切向并使四片刀口處于同一平面，然后擰緊5十字螺釘即可。
2、儀器底部有真紋刻痕，用于固定式樣，便于切割，防止試樣打滑。
3、波紋手輪下有滾花刻盤，可以用來調整所切厚度，具體做法為：松開件3鎖緊螺釘，旋轉件2滾花刻盤（順時針減少，逆時針增加）。至所取厚度值，鎖緊件3鎖緊螺釘即可。
Structure and adjustment of tcgb-19 electric geotextile Sampler:
1. The cutter blade is a double-sided blade with four pieces, which are round and evenly distributed. The blade can be replaced. The specific operation is as follows: loosen the cross screw of Part 5 (there are 4 screws on each piece), remove the blade pressing plate of Part 6 and the sampling blade of Part 4, replace with a new blade, press on the blade pressing plate of Part 6, pay attention to make the blade edge clockwise and make the four blade edges in the same plane, and then tighten the cross screw of Part 5.
2. There is a real mark on the bottom of the instrument, which is used to fix the pattern, easy to cut and prevent the sample from slipping.
3. There is a knurled plate under the corrugated handwheel, which can be used to adjust the cutting thickness. The specific method is as follows: loosen the locking screw of Part 3, and rotate the knurled plate of Part 2 (decrease clockwise, increase counterclockwise). To the thickness value, the locking part 3 can lock the screw.
使用方法
四、TCGB-19型電動土工布取樣器使用方法：
四、TCGB-19型電動土工布取樣器使用方法：
1、取待裁織物，量好厚度，按上述調整好取樣器刻盤。
2、將待織物平鋪軟木墊上，將圓盤取樣器放在織物上，一手扶住外罩7，一手握住波紋手輪1，并旋加一定壓力，然后順時針旋轉波紋手輪1（轉角>90度）即可將圓試樣截取。
五、TCGB-19型電動土工布取樣器注意事項：
1、本儀器刀片刀口很鋒利，使用中不得將手放在底部，以免損傷。
2、本儀器裁取試樣應在軟木墊上進行，儀器不用時擦拭干凈，置于儀器盒中，以免儀器損壞。
使用一段時間后如刀片不鋒利，按3.1條更換刀片。
主營產品：土工檢測儀器,防水材料檢測儀器,陶瓷磚檢測儀器,水利水電粗粒土系列,瀝青儀器檢測儀器
Main products: geotechnical testing instrument, waterproof material testing instrument, ceramic brick testing instrument, water conservancy and hydropower coarse-grained soil series, asphalt testing instrument
