一、產品簡介：
水泥恒溫水養護箱是的水泥膠砂水養護設備，水泥恒溫水養護箱是根據新標準GB/T17671-1999、ISO679-1989《水泥膠砂強度檢測方法》(ISO法)中對水泥膠砂試件的養護要求設計生產的，具有操作簡單控溫精度高和外形美觀等觀點，水泥恒溫水養護箱內膽和水槽全部采用不銹鋼板制做，溫度控制采用電腦智能儀表，外門采用雙層真空玻璃門。
The cement constant temperature water curing box is the cement cement sａnd water curing equipment. The cement constant temperature water curing box is based on the new standards GB / T17671-1999 and ISO679-1989 "Cement rubber sａnd strength testing method" (ISO method). Sａnd specimens are designed and produced with maintenance requirements. They have simple operation, high temperature control accuracy, and beautiful appearance. The inner tank and water tank of the cement constant temperature water curing box are all made of stainless steel. Floor vacuum glass door.
二、技術參數：
★電源：220V±10%
★箱內尺寸：520*450*880mm
★容量：軟練試模40*40*160 可放174只
★外形尺寸：770*670*1580mm
★恒溫水溫：20℃±1℃可調 顯示精度0.1℃
★制冷功率：150W
★加熱功率：600W
★風機：45W
★重量：120Kg
Technical parameters of HBY-30 cement constant temperature water curing box:
★ Power supply: 220V ± 10%
★ Box size: 520 * 450 * 880mm
★ Capacity: Soft test model 40 * 40 * 160 can hold 174
★ Dimensions: 770 * 670 * 1580mm
★ Constant water temperature: 20 ℃ ± 1 ℃ adjustable Display accuracy 0.1 ℃
★ Cooling power: 150W
★ Heating power: 600W
★ Fan: 45W
★ Weight: 120Kg
三、原理及結構：
★分池式水泥恒溫水養護箱箱體采用優質鋼板制作，內膽及分池水槽全部為不銹鋼材料，具有很好的耐腐蝕性和導熱性。分池水槽配置滑動輪與導軌，可很方便地推拉和取出。
★養護箱采用智能化數顯溫度控制儀，當水溫高于或低于所設定的溫度時，自動切換加熱管或制冷機工作，產生冷氣或暖氣，再通過箱內特別按裝的離心風機，可迅速地均勻空氣溫度，使水溫保持在20℃±1℃范圍內。
HBY-30 cement constant temperature water curing box principle and structure:
★ The tank type cement constant temperature water curing box box is made of high quality steel, and the inner tank and the tank water tank are all stainless steel materials, which has good corrosion resistance and thermal conductivity. The sub-tank water tank is equipped with sliding wheels and guide rails, which can be easily pushed and pulled out.
★ The maintenance box adopts an intelligent digital temperature controller. When the water temperature is higher or lower than the set temperature, the heating pipe or refrigerator is automatically switched to work to generate cold air or heating, and then the centrifugal fan installed in the box is specially installed. , Can quickly uniform air temperature, so that the water temperature is maintained within the range of 20 ℃ ± 1 ℃.
四、使用方法：
★儀器應按放在無強烈振動和無腐蝕性氣體的清潔環境中，使用環境溫度應在0-38度以內，使用環境濕度小于85%HR，確定供電電壓應在220V范圍內，并提供良好的接地保護裝置或漏電保護器。
★打開外門拉出底部任何一只分池水槽取下后，再把內膽底部的水盒內加滿水，并將傳感器頭浸入水中。再把分池水槽內加至約13CM左右的清潔水后放入框架內。(水平面要超過試件2cm左右)。
★打開電源開關，檢查溫度設定值，儀表進入工作狀態，開機工作5小時左右，待水溫到達所需的溫度后再放入試件。
★分池水槽換水時，可拉出水箱再向上抬出，清洗完后放回原處，再注入預先準備好的清潔水。
HBY-30 cement constant temperature water curing box use method:
★ The instrument should be placed in a clean environment without strong vibration and non-corrosive gas. The use environment temperature should be within 0-38 degrees, and the use environment humidity should be less than 85% HR. It should be determined that the power supply voltage should be within 220V and provide a good Ground protection or earth leakage protector.
★ Open the outer door and pull out any sub-tank water tank at the bottom. Then fill the water tank at the bottom of the inner tank with water and immerse the sensor head in the water. Then add the clean water in the sub-tank water tank to about 13CM and put it into the frame. (The horizontal plane should be about 2cm above the test piece).
★ Turn on the power switch, check the temperature setting value, the meter enters the working state, and start working for about 5 hours, and then put the test piece after the water temperature reaches the required temperature.
★ When changing the water in the sink, you can pull out the water tank and lift it up again. After cleaning, put it back in place and fill it with clean water prepared in advance.
