国产精品成人网站,日韩视频二区,亚洲成人手机电影,怡红院国产

WSS、WSSX系列

WSS, WSSX Series

工業雙金屬溫度計

Industrial double metal thermometer

說

明

書

Manual

• 用途

雙金屬溫度計是一種適合測量中、低溫的現場檢測工業儀表?？捎脕碇苯訙y量氣體、液體和蒸汽的溫度。帶電接點雙金屬溫度計，并能在工作溫度超過給定值時，自動發出控制信號切斷電源或報警。

     雙金屬溫度計具有無汞害、易讀數、堅固和耐振等優點，可代替工業玻璃水銀溫度計廣泛適用于工業和科研部門。

     雙金屬溫度計分為普通型、戶外型、防腐型三種。普通型外殼用鐵皮電鍍，保護管用不銹鋼，適用于室內一般場合使用。戶外型外殼用鋁金制造，保護管，連接柱均采用不銹鋼，密封性較好，適用于室內外，一般耐腐蝕場所。防腐型外殼采用全不銹鋼，保護管、連接柱可用鉬二鈦材料，連接部分均采用密封膠，可適用于多數腐蝕介質、氣體的測量。

• 結構原理

雙金屬溫度計感溫元件采用多圈直螺旋形雙金屬片。一端固定，另一端（自由端）連接在芯軸上，軸向型溫度計指針直接裝在芯軸上。徑向型結構指示針通過轉角彈簧與芯軸連接。當溫度變化時，感溫元件自由端旋轉，經芯軸傳動指針在刻度盤上指示被測介質溫度的變化值。

電接點溫度計，指針上裝有動接點，固定接點裝在設業指針上指針觸頭隨溫度變化旋轉，當溫度達到或超過設定值時，接點閉合發出信號，以達自動控制和報警的目的。

• 主要技術參數

1. 溫度計為軸向型、徑向型、135°三種型式。
2. 溫度計的精度等級為1級、1.5級。
3. 溫度計的測量范圍見表一。
4. 溫度計的時間常數不超過40S。
5. 保護管的材料為1Cr18Ni9Ti不銹鋼和鉬二鈦，其所能承受的分稱壓力為6.4MaP。
6. 溫度計分普通型、戶外型、防腐型三種型式。
7. 溫度計的接點為上、下限，單限，雙上限（全部常開）。
8. 接點額定功率：10VA（無感負載）。

zui高工作電壓：220V。

zui大工作電流：1A。

1. 指示表頭使用環境溫度-40~85℃。
2. 指示表頭使用環境濕度5~。
3. WSS系列雙金屬溫度計屬于耐震機械儀表。
4. 測量溫度時應將保護管下面100mm長全部浸入被測量介質，以保持溫度準確性。
5. 執行標準：JB/T8803-1998

• 型號表示方法

雙金屬溫度計型號的組成

W     S       S     X               4      1     1

*位 第二位 第三位 第四位          *位 第二位 第三位

*節                             第二節

型號示例：

表殼公稱直徑為φ100（mm）的軸向式普通型雙金屬溫度計，安裝方式為可動外螺紋。

型號表示：WSS-401。

• 接點接線示意

• 型號、規格、參考價

注：0-50℃表尾長≥100mm，WSS-481W請注明軸芯式。

• 型號與尺寸

• 使用和維護

1. 雙金屬溫度計保護管浸入被測介質中的長度必須大于感溫元件的長度，一般浸入長度大于100mm，0-50℃量程的浸入長度大于150mm，以保證測量的準確性。
2. 雙金屬溫度計在保管、使用安裝及運輸中，應避免碰撞保護管，切勿使保護管彎曲變形及將表殼當扳手使用。
3. 各類雙金屬溫度計不宜用于測量敞開容器內介質溫度，帶接點溫度計，不宜在工作振動較大場合的控制回路中使用。
4. 溫度計在正常的情況下，應予定期檢驗。一般以每隔6個月檢驗一次為宜。
5. 電接點溫度計不允許在強烈震動下工作，以免影響接點可靠性。
6. WSS萬向型溫度計的波紋管只有0.1mm厚，所以轉向時必須旋松M4螺母、螺絲。并小心轉向，切勿用力。安裝時必須用兩把扳手，以免損壞。
7. 本產品實行三包。

• 訂貨須知

1. 訂貨時須寫明產品的型號、測量范圍、安裝螺紋、保護管長度，外殼公稱直徑、精度級別等技術參數。
2. 需要戶外型和防腐品種的須注明。
3. 用戶有特殊要求時，須具體注明。

• Use

Two-metal thermometer is a suitable measure, the low temperature of the industrial scene detection instruments. Can be used to direct measurement of gas, liquid and steam temperature. Charged contact bimetallic thermometer and can work in temperature over a given value, the automatic control signals cut off the power or the police.
      Bimetal thermometers with mercury-free harm, easy reading, strong and resistant to vibration, and other advantages, instead of industrial glass mercury thermometers widely applied to industrial and scientific research departments.
      Two-metal thermometer into ordinary type, outdoor type, preservative-three. Ex-general with shell plating, stainless steel and effective protection, apply to indoor use of general occasions. Al-casing of the outdoor production, protection of connecting the columns are stainless steel, seal better, apply to indoor and outdoor, general corrosion-resistant places. Use of all anti-corrosion stainless steel casing, the protection of linking the two molybdenum-titanium materials can be used to connect parts of a sealant, applicable to most corrosive medium, the gas measurement.

• the structure principle

Two-metal thermometer temperature components used more laps straight double-helix-shaped metal sheets. One end fixed, the other side (the Liberal side) connected to the Mandrel, axial-pointer directly with the thermometer on the Mandrel. Radial-type structure through direct contacts with the corner of Spring Mandrel connection. When the temperature changes, temperature-free components rotation, the Mandrel transmission pointer in the dial on the instructions of the change in temperature measured media value.
    Xinhua contact thermometer, with indicators on the dynamic contact, in constant contact with the guidelines established guidelines on contact with the temperature changes in rotation, when the temperature reached or exceeded settings, close contact sent a signal to achieve the purpose of automatic control and alarm.

• the main technical parameters

1, the thermometer for the axial type, radial-type, 135 ° three types.
2, the accuracy of the thermometer as a class, 1.5.
3, the thermometer measured the scope of a table.
4, the time constant temperature not exceeding 40 S.
5, the protection of the materials for 1 Cr18Ni9Ti stainless steel and titanium molybdenum Second, the points that can bear the pressure of 6.4 MaP.
6, the thermometer at ordinary type, outdoor type, three types of anti-corrosion.
7, the contact point for the thermometer on the floor, single-limit, double the ceiling (all normally open).
8, contact Power Rating: 10 VA (no flu load).
The maximum operating voltage: 220 V.
The largest current work: 1 A.
9, the first direct use of environmental temperature table -40 ~ 85 ℃.
10, directed the first use of the environment in Table 5 to 100 percent humidity.
11, WSS series of dual-metal thermometer Seismic mechanical meters.
12, the temperature measurement should be the protection of below 100 mm long been immersed all media measurement, in order to maintain temperature accuracy.
13, implementation of the standards: JB/T8803-1998

• models that way

Double models thermometers metal components

W     S       S     X               4      1     1

first second third fourth                 first second third

Section 1                                Section II

Model examples:

Case said the diameter of φ100 (mm) of the general-axial dual-metal thermometer, for the installation of movable thread.

Model said: WSS-401.

• contact indicate wiring

• models, specifications, the reference price

Note :0-50 ℃ table tail length ≥ 100 mm, WSS-481W-please specify core axis.

• model and size

• use and maintenance

1, double the protection of submerged metal thermometer measured the length of medium temperature must be greater than the length of components, the general immersion longer than 100 mm ,0-50 ℃ range greater than the length of immersion 150 mm, to ensure the accuracy of measurement.
2, double-metal thermometer in custody, installation and use of transport, protection of the collision should be avoided, not to make the protection of deformation and Case will use the wrench.
3, various types of dual-metal thermometer should not be used to measure open containers medium temperature, contact with the thermometer, it is not appropriate in the work of vibration larger occasions the use of the control loop.
4, the thermometer under normal circumstances, should be regularly inspected. General every six months to test a suitable.
5, electrical contacts are not allowed in the thermometer under strong vibration, so as not to affect contact reliability.
6, WSS universal bellows-type thermometer only 0.1 mm thick, so to the time of spin-M4 nuts, screws. And to carefully and not forced. Installation of two wrenches to be used, so as to avoid damage.
7, the Three Guarantees products.

• ordering notes

1, ordering products to be specified the type, range, the installation thread, the protection of the length of the shell diameter, precision-level and other technical parameters.
2, and the preservation needs of outdoor-type varieties must state.
3, users with special requirements, the need to specify.