儀表電纜實驗報告
安徽天彩電纜集團有限公司
電力電纜產品出廠試驗報告單
Power cable test report
計劃單號Contract No.:201805046
型號規 Specifications :ZR-YJV22 3*50+2*25mm2
檢驗批號Inspection Lot number:201805046-01
額定電壓Rated voltage:0.6/1 kV
產品標準Product Standards:GB/T12706 -2008 數 量Quatity:250米
序號No. | 檢 驗 項 目 Test Item | 單 位Unit | 標 準 值Standard Value | 實 測 值Measured value | 單項評定Individual assessment |
1 | 結構尺寸檢查 Structural Inspection |
|
|
|
|
1.1 | 導體中少單線根數 The minimum number of single wires in the conductor | 根 | 6 | 10 10 10 | 合格qualified |
1.2 | 絕緣厚度 Insulation thickness |
|
|
|
|
| —— 平均厚度Average thickness ≥ | mm | 1.0 | 1.0 1.0 1.0 | 合格qualified |
| —— BO厚度 Thinnest thickness ≥ | mm | 0.80 | 0.95 0.95 0.96 | 合格qualified |
| —— 顏色 Color |
|
|
|
|
1.3 | 內護層厚度 Inner sheath thickness | mm | 0.4 | 0.4 | 合格qualified |
1.4 | 鎧裝 Armoured 鋼帶層數/厚度Steel tape layers/Thickness | 2/ mm | 2/0.5 | 2/0.5 | 合格qualified |
| 寬度 Width | mm | 35 | 35 | 合格qualified |
1.5 | 護套 Sheath |
|
|
|
|
| ——平均厚度 Average thickness | mm |
| 1.8 | 合格qualified |
| ——BO厚度 Thinnest thickness ≥ | mm | 1.24 | 1.70 | 合格qualified |
1.6 | 電纜外徑 Cable outer diameter | mm |
| 33.7 | 合格qualified |
2 | XLPE絕緣熱延伸試驗 XLPE insulation thermal extension test 負荷Load:20N/cm2,200℃/15min |
|
|
|
|
2.1 | 負載下伸長率 Elongation under load ≤ | % | 175 | 130 | 合格qualified |
2.2 | 冷卻后永JIU伸長率 Permanent elongation after cooling ≤ | % | 15 | 4 | 合格qualified |
3.1 | 20℃時導體電阻 Conductor resistance at 20°C ≤ | Ω/km | 0.387 | 0.384 0.384 0.384 | 合格 |
3.2 | 成品交流電壓試驗 Product AC voltage test | kv/ min | 3.5/5 | 不擊穿 Does not break down | 通過 |
4 | 表觀Exterior |
|
|
|
|
4.1 | 標志間距離 Distance between signs ≤ | mm | 550 | 380 | 符合 |
4.2 | 標志/表觀Sign/Exterior | 內容完整,清晰耐擦/光潔圓整The content is complete, clear and clean/ Not easy to erase | 符合 | ||
結論: Conclusion 經檢驗,產品符合GB/T12706 -2008標準要求,準予出廠。 After inspection, the product meets the requirements of GB/T12706-2008 standard and is approved for delivery
|
檢驗/日期: 審核/日期:
Inspection Date Audit/Date