江蘇春晨電纜有限公司：http://caturday.cn/st82365/

電纜應用：JG硅橡膠電機引接線
微電機、變頻電機、電機控制器、Y系列電機等H級絕緣及以下

移動電器、電動工具、JG硅橡膠電機引接線，儀器儀表、電子設備、電信機房、成套控制柜、照明工程、機械設備及自動化裝置的移動連接，

1 scope of application

本標準適用于交流額定電壓450/750V及以下動力、日用電梯、儀器儀表及電信設備用的銅芯聚氯乙烯絕緣電纜（電線）的成品檢驗。

This standard applies to the AC rated voltage 450/750V and the following power, daily lift, instruments and meters and ecommunications equipment used in copper conductor PVC insulated cables (wires) of the finished product inspection.

本標準適用于GB/T5023-2008中規定的型號和規格。

This standard applies to GB/T5023-2008 in the model and specification.

2 標準依據

2 standard basis

GB/T5023.1-2008 額定電壓450/750V及以下聚氯乙烯絕緣電纜

GB/T5023.1-2008 rated voltage 450/750V and below PVC insulated cables

第1部分：一般要求

The first part: General requirements

GB/T5023.2-2008 額定電壓450/750V及以下聚氯乙烯絕緣電纜

GB/T5023.2-2008 rated voltage 450/750V and below PVC insulated cables

第2部分：試驗方法

Second part: Test Method

GB/T5023.3-2008 額定電壓450/750V及以下聚氯乙烯絕緣電纜

GB/T5023.3-2008 rated voltage 450/750V and below PVC insulated cables

第3部分：固定布線用無護套電纜

Third part: non - sheathed cable for fixed wiring

GB/T5023.4-2008 額定電壓450/750V及以下聚氯乙烯絕緣電纜

GB/T5023.4-2008 rated voltage 450/750V and below PVC insulated cables

第4部分：固定布線用護套電纜

Fourth part: sheath cable for fixed wiring

GB/T5023.5-2008 額定電壓450/750V及以下聚氯乙烯絕緣電纜

GB/T5023.5-2008 rated voltage 450/750V and below PVC insulated cables

第5部分：軟電纜（軟線）

The fifth part: soft cable (wire)

3 檢驗項目

3 inspection items

3.1 固定布線用無護套電纜檢驗項目見表1。

3.1 fixed wiring with non - sheathed cable inspection items see table 1.

3.2 固定布線用護套電纜檢驗項目見表2。

3.2 fixed wiring with sheathed cable inspection items see table 2.

3.3 軟電纜（軟線）檢驗項目見表3。

3.3 soft cable (cord) inspection items are shown in table 3.

3.4 成品電纜標志

3.4 finished cable mark

成品電纜護套表面上應有制造廠名、產品型號規格、額定電壓及相應的強制性標識的連續標志，標志應字跡清楚，容易辨認、耐擦，成品電纜的標志應符合GB6995.3的規定。

The surface of finished cable sheath should be the manufacturer name, product specifications, rated voltage and the corresponding mandatory labeling continuous mark, logo should be legible, identifiable, rub resistant, symbol of the finished cable shall comply with the provisions of GB6995.3.

4 檢驗規則

4 inspection rules

4.1 產品由質量管理處檢查合格后方能出廠，每個出廠包裝件上應附有產品質量合格證。

4.1 products by the quality management department to check the qualified rear can be manufactured, each factory packaging parts should be accompanied by a certificate of product quality.

4.2 產品按第3條規定的試驗項目進行試驗。

4.2 products according to the provisions of the third test project.

4.3 產品按以下試驗頻度進行抽樣試驗。

4.3 products according to the following test frequency sampling test.

4.3.1 結構尺寸檢查應在每批同一型號及規格中的一根制造長度電纜上進行，其數量應不超過交貨批長度數量的10%。

4.3.1 structure size inspection shall be carried out on one of the same type and size of the manufacturing length cable, the number of which shall not exceed 10% of the quantity of the delivered goods.

4.3.2 如果*次試驗結果不符合第3條規定抽檢的任一項要求，應在同一批電纜中再取雙倍試樣就不合格項目進行試驗，仍不合格時，應試驗。

4.3.2 if the first test results do not conform to the provisions of article third any sampling requirements, should be in the same batch of cables then double samples is unqualified project test, still unqualified, test.

5 包裝

5 packaging

5.1 電纜應妥善包裝在符合JB/T 8137規定要求的電纜盤上交貨。

5.1 cable should be properly packaged in line with the requirements of JB/T 8137 on the cable tray delivery.

5.3 每圈或每盤導線上應附有標簽標明：

5.3 each lap or on each set of wires shall be marked with Tags:

制造廠名稱；

Name of manufacturer;

型號及規格；

Model and specifications;

額定電壓；

Rated voltage;

長度；

Length;

重量；

Weight;

制造日期：年 月 ；

Date of manufacture: years;

產品編號或認證標志；

Product number or certification mark;

電纜盤正確旋轉方向等。

Correct rotation direction of cable tray, etc..

表1

Table 1

序號 試驗項目 試

Serial number test item test

驗

Check

類

class

型 GB/T5023.3條文號 試驗方法

A number of test methods GB/T5023.3

60227

Sixty thousand two hundred and twenty-seven

IEC

IEC

01

01

(BV) 60227

(BV) 60227

IEC

IEC

02

02

(RV) 60227

(RV) 60227

IEC

IEC

05

05

(BV) 60227

(BV) 60227

IEC

IEC

06

06

(RV) 60227

(RV) 60227

IEC

IEC

07

07

(BV-90) 60227

(BV-90) 60227

IEC

IEC

08

08

(RV-90) GB/T 條文號

(RV-90) GB/T number

1 結構尺寸檢查

1 structural dimension inspection

1.1 導體結構 S 2.3.1 3.3.1 4.3.1 5.3.1 6.3.1 7.3.1 檢查和試驗

1.1 conductor structure 2.3.1 3.3.1 4.3.1 5.3.1 6.3.1 7.3.1 S inspection and testing

1.2 絕緣厚度 S 2.3.2 3.3.2 4.3.2 5.3.2 6.3.2 7.3.2 5023.2 1.9

1.2 insulation thickness 2.3.2 3.3.2 4.3.2 5.3.2 6.3.2 7.3.2 S 1.9 5023.2

1.3 外徑 S 2.3.3 3.3.3 4.3.3 5.3.3 6.3.3 7.3.3 5023.2 1.11

1.3 outside diameter 2.3.3 3.3.3 4.3.3 5.3.3 6.3.3 7.3.3 S 1.11 5023.2

2 20℃導體電阻試驗 S 2.3.1 3.3.1 4.3.1 5.3.1 6.3.1 7.3.1 5023.2 2.1

220 conductor resistance test 2.3.1 3.3.1 4.3.1 S 5.3.1 6.3.1 7.3.1 2.1 5023.2

3 成品電纜電壓試驗

3 finished cable voltage test

3.1 2500V S √ √ 5023.2 2.2

3.1 2500V S 5023.2 2.2 tick tick

3.2 2000V S √ √ √ √ 5023.2 2.2

3.2 2000V S 5023.2 2.2 tick tick tick tick

表2

Table 2

序號 試驗項目 試驗類型 GB/T5023.4條文號 試驗方法

Number of test items test type GB/T5023.4 number test method

60227IEC10(BVV) GB/T 條文號

60227IEC10 (BVV) GB/T number

1 結構尺寸檢查

1 structural dimension inspection

1.1 導體結構 S 2.3.1 檢查和試驗

1.1 conductor structure 2.3.1 S inspection and testing

1.2 絕緣厚度 S 2.3.2 5023.2 1.9

1.2 insulation thickness 2.3.2 S 1.9 5023.2

1.3 外徑 S 2.3.5 5023.2 1.10

1.3 outside diameter 2.3.5 S 1.10 5023.2

1.4 護套厚度 S 2.3.6 5023.2 1.11

1.4 sheath thickness 2.3.6 S 1.11 5023.2

1.5 橢圓度 S 2.3.6 5023.2 1.11

1.5 degree 2.3.6 S 1.11

2 20℃導體電阻試驗 S 2.3.1 5023.2 2.1

220 conductor resistance test 2.3.1 S 2.1 5023.2

3 成品電纜電壓試驗

3 finished cable voltage test

3.1 2000V S √ 5023.2 2.2

3.1 2000V S 5023.2 V 2.2

表3

Table 3

序號 試驗項目 試驗類型 GB5023.5條文號 試驗方法

Number of test items test type GB5023.5 number test method

60227IEC52

60227IEC52

(RVV) 60227IEC53

(RVV) 60227IEC53

(RVV) GB/T 條文號

(RVV) GB/T number

1 結構尺寸檢查

1 structural dimension inspection

1.1 導體結構 S 5.3.1 6.3.1 檢查和試驗

1.1 conductor structure 5.3.1 6.3.1 S inspection and testing

1.2 絕緣厚度 S 5.3.2 6.3.2 5023.2 1.9

1.2 insulation thickness 5.3.2 6.3.2 S 1.9 5023.2

1.3 外徑 S 5.3.4 6.3.4 5023.2 1.10

1.3 outside diameter 5.3.4 6.3.4 S 1.10 5023.2

1.4 護套厚度 S 5.3.5 6.3.5 5023.2 1.11

1.4 sheath thickness 5.3.5 6.3.5 S 1.11 5023.2

1.5 橢圓度 S 5.3.5 6.3.5 5023.2 1.11

1.5 degree S 5.3.5 6.3.5 1.11 5023.2

2 20℃導體電阻試驗 S 5.3.1 6.3.1 5023.2 2.1

220 conductor resistance test 5.3.1 6.3.1 S 2.1 5023.2

3 成品電纜電壓試驗

3 finished cable voltage test

3.1 2000V S √ √ 5023.2 2.2

3.1 2000V S 5023.2 2.2 tick tick

注：1、絕緣火花試驗應進行。

Note: 1, insulation spark test should be carried out in .

2、導通試驗適用于屏蔽電線和安裝用電線，應檢查。

2, conduction test is suitable for shielding wire and installation of wires, should be .

3、其它抽樣項目應逐批檢查。

3, other sampling items should be examined by batch.