West P6100 1/16 DIN 通用型過程控制器
無跳線配置
- 自整定
- 自動檢測硬件
- 加熱/冷卻操作
- 過程和回路報警
- 設定點斜率
- Modbus 和 ASCII 通訊
遠程/雙設定
West P6100 1/16 Din Process Controller
With its improved interface, technical functionality and field flexibility, the West 6100 gives you the best in comprehensive control for most temperature and process control loops.
• Jumper less Configuration
• Auto or Manual Tuning
• Auto Detected Hardware
• Heat/Cool Operation
• Process & Loop Alarms
• Ramping Set point
• Modbus & ASCII Comms
• Remote/Dual Set point Options
West P6100 1/16 DIN 通用型過程控制器
籍其友好的用戶界面、強大的技術功能以及靈活的現場配置，West P6100 在溫
控與過程控制領域表現出的性能。
- 無跳線配置
- 自整定
- 自動檢測硬件
- 加熱/冷卻操作
- 過程和回路報警
- 設定點斜率
- Modbus 和 ASCII 通訊
- 遠程/雙設定
West P6700 1/16 DIN FM Approved Limit Controller
• High or low limit control.
• Storage of peak temperature plus duration of alarm condition.
• Plug and Play Technology allows field upgrades.
• Dedicated configuration port allows configuration directly from PC for fast and repeatable configurations.
• Password protection limiting operator access and providing process security.
• Display process value, set point or both.
The 6700 provides a latched relay output which is activated
when process parameters either exceed or fall
below the desire value, providing a fail safe cutoff which
has to be manual reset once the process returns to a
safe condition. This limit controller is FM approved.
West P6700 1/16 DIN 限位控制器
West P6700 是一種可編程的安全切斷裝置，報警和指示燈輸出任選。當超過安全值
時，自鎖繼電器會切斷電源，過程必須在復位后才能繼續。它擁有改進的P 系列硬件以及友好的用戶界面，使用起來更容易。
- 高或低報警脫扣
- 無跳線組態
- 5A 自鎖限位繼電器
- 自動檢測硬件
- 遠程復位選件
- Modbus 和 ASCII 通訊
- 超限和繼電器指示燈
- 2 個報警器或指示燈
West P4170 1/4 DIN Valve Motor Drive Controller
• Open loop control eliminates the need for slidewire feedback.
• Plug and Play Technology allows for field upgrades.
• Dedicated configuration port allows configuration directly from PC for fast and repeatable configurations.
• Two Auto-tune algorithms: Pre-tune plus Self-tune.
• Third output for alarm or retransmission output.
The 4170 is a 1/4 DIN controller with continuous online
open loop control of valve motor drives or electric
actuators. This feature allows for accurate control without
the need for slidewire feedback. This lowers the
cost of the motor and wiring, without sacrificing control.
West P4170 1/4 DIN 閥位控制器
West P4170 是一種專為控制閥位馬達設計的過程控制器，配有*的閥位控制算法，無需閥位反饋信號。
- 電動閥門控制
- 設定點斜率
- 2 個過程報警
- 自整定
- 回路報警
- 雙設定點
- RS485 通訊
- 計算機組態
West P8010 1/8 DIN Indicator
• Large four digit display available in green or red.
• Alarms can be latching or non latching.
• Two or three alarms available.
• Plug and Play Technology allows field upgrades.
• Dedicated configuration port allows configuration directly from PC for fast and repeatable configurations.
West P8010 1/8 DIN 數字顯示器
West P8010 是一種基于微處理器的 1/8 DIN 數字顯示器。可以是紅色或綠色顯
示。標配有一個自鎖繼電器，通過插件可以加入兩個報警繼電器、變送輸出或變送器電源模塊。
- 4 位 LED 顯示
- 工程單位顯示
- zui多3 個報警輸出
- 計算機組態
- 變送器電源（可選）
- 過程值變送輸出（可選）
- zui小/zui大值保持
- RS485 通訊選件
West 8170 1/8 DIN Valve Motor Drive Controller
• Open loop control eliminates the need for slidewire feedback.
• Plug and Play Technology allows for field upgrades.
• Dedicated configuration port allows configuration directly from PC for fast and repeatable configurations.
• Two Auto-tune algorithms: Pre-tune plus Self-tune.
• Third output for alarm or retransmission output.
West P8170 1/8 DIN 閥位控制器
West P8170 是一種專為控制閥位馬達設計的過程控制器，配有*的閥位控制算
法，無需閥位反饋信號。
- 電動閥門控制
- 設定點斜率
- 2 個過程報警
- 自整定
- 回路報警
- 雙設定點
- RS485 通訊
- 計算機組態
West MLC 9000+ CANopen Bus Communications Module
The CANopen Bus Communications Module （BCM） is part of the MLC 9000+ DIN-Rail mounting PID control system. The BCM handles communication between up to 8 single or multi loop controller modules and the CANopen network. Systems larger than 32 loops can be built using multiple BCMs, within the limitations of your CANopen system.
- CANopen port
- Software Configurable
- Supports up-to 1024kbps
- Configuration port
- DIN Rail Mounting
- Configurable Data Assemblies
West MLC 9000+ CANopen 總線模塊
CANopen 總線模塊是 MLC 9000+ 多回路 PID 控制系統的一部分。該總線模塊是 MLC 9000+ 系統中的管理員，用于管理與zui多 8 個單回路或多回路模塊以及 CANopen 網絡的通訊。當構建大于32 個回路的系統時，可以在CANopen 系統支持的網絡范圍內使用多個總線模塊。
- CANopen 端口
- 可由軟件組態
- 支持zui高 1024kbps
- 組態端口
- DIN 導軌安裝
- 可組態數據鏈接
