主要特點Main features:
Open type vertical heating furnace,tube and flange can pivot and move away from chamber.
開啟式立式加熱體,爐管法蘭可繞軸旋轉移出爐腔。
With standard configuration of OD60mm quartz tube and 20T electrical press
標配Φ60mm石英管真空密封,20T電動壓力機。
Adopt graphite push rod and mould,at the same time of pressing,heat the powder to common sintering temperature or lower,to get the dender and uniform product after a short time
采用石墨頂桿和石墨模具,在加壓的同時使粉末加熱到正常燒結溫度或更低一些,經過較短時間燒結成致密而均勻的制品。
技術參數Technical Parameters:
Power 輸入電源 | Power rated: 2KW 額定功率:2KW | ||||
Voltage 電壓 | Voltage rated: AC220V 50/60HZ 額定電壓:AC220V 50/60HZ | ||||
Working Temperature 工作溫度 | Max. Temperature: 1200℃( 1 hr) 溫度:1200℃ (1小時) Continuous working temperature: ≤1150℃ 持續工作溫度:≤1150℃ Max.heating Rate: ≤10℃/min 升溫速率:≤10℃/分 | ||||
控溫方式 | PID automatic control and auto-tune function. 模糊PID控制和自整定調節 30 programmable segments for precise thermal processing. 智能化30段可編程控制 Built-in protection for the over-heated and broken thermocouple. 超溫和斷偶報警功能 | ||||
Heating Elements 加熱元件 | Resistance wire, Fe-Cr-Al Alloy doped by Mo 電阻絲(摻鉬鐵鉻鋁合金) | ||||
Temperature Accuracy 控溫精度 | +/- 1℃ | ||||
Prosessing tube 爐管 | Φ60*350mm | ||||
Graphite rod diameter 石墨壓桿直徑 | 48mm | ||||
Pressure maintain time 保壓時間 | 0-50min | ||||
Movable distance 壓力行程 | 50mm | ||||
Plunger diameter 活塞直徑 | 87mm | ||||
Pressure stability 壓力穩定性 | ≤1MPa/5min | ||||
Weight 重量 | 300kg | ||||
Vacuum Flange 真空法蘭 | Special designed flanges 定制法蘭 | ||||
Vacuum Pressure 真空壓力 | 1pa can be achieved by mechanical pump 機械泵可達1pa 10^-4 pa can be reached by molecular pump 分子泵可達10^-4pa Please click the picture below to order vacuum parts 點擊下列圖片訂購真空部件
| ||||
Warranty 質保 | One year limited warranty with lifetime support (Such consumable parts as tO-rings, etc. are NOT supported by the warranty) 一年質保終身支持(消耗品如O型圈等不在質保范圍內) | ||||
Warning 注意事項 | Graphite must used under anaerobic condition 石墨必須絕氧使用 Considering contact area calculate pressure 計算壓強時應考慮接觸面積 Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating. 在使用過程中爐膛表面可能出現細小裂紋。這是正常情況,裂紋可以用氧化鋁涂層修復。 | ||||
Compliance 認證 | CE Certified CE認證 The furnace is ready to pass TUV (UL61010) or CSA certification at extra cost. 可付費進行TUV(UL61010)或CSA認證 | ||||
Operation instructions 操作指導 | Click to download the operating manual 點擊下載說明書 |