SC-010Dust Test Chamber沙塵試驗箱
1  Key Technical Specifications/主要性能參數:
 
  1.1  Equipment: Dust Test Chamber
        設備名稱:沙塵試驗箱
  1.2   Model:SC-010
        型號：SC-010
  1.3  USEFUL CAPACITY: 1000 liters approx
       有效容積：約1000升
  1.4  Internal dimension: W×D×H=1000mm×1000mm×1000mm,
       內部尺寸：寬1000mm×深1000mm×高1000mm，含局部突出的部分；
       Exterior dimension: approx. W×D×H=1500mm×1600mm×2000mm;
       外部尺寸：大約寬1500mm×深1600mm×高2000mm
  1.5  Temperature range: RT+5～+50℃;adjustable
       溫度范圍：房間溫度+5～+50℃，可調
  1.6  Humidity range: natural humidity without control;
       濕度范圍：環境自然濕度，不控制；
  1.7  Dust concentration: 2kg/m3;
       粉塵濃度：2kg/m3；
  1.8  Dust specification/粉塵規格:
       The talcum powder can pass through a square-meshed sieve the nominal wire diameter of which
       is 50μm and the nominal width of the gap between wires is 75μm;
       粉塵規格：能通過篩孔為75um,金屬直徑為50um 的方孔干燥；
  1.9  Air velocity: ≤2m/s;
       試驗風速：≤2m/s
  1.10  Pressure difference inside specimen/試件差壓:
       1.10.1 Method A: 1.98KPa lower than the atmospheric pressure;
       1.10.2 Method B: the same as the atmospheric pressure;
                模式A：比大氣壓低1.98Kpa
                模式B：和大氣壓一樣
 
2  Cabinet Structural Features/箱體結構特性:
 
  2.1 Exterior shell materials: Plastic-sprayed steel-tin, tephrosious colored t=1.0mm;
     噴塑鋅鋼板，白灰色厚度=1.0mm
  2.2 Interior shell materials: SUS304 stainless steel plate t=1.0mm;
     內部材料：SUS304不銹鋼板厚度=1.0mm
  2.3 Standard configuration/標準配置:
     2.3.1 One porthole (Ф100mm), equipped with blind plugs of low thermal conductivity materials
          一個測試孔(Ф100mm)，，配有低導熱性材料的絕緣塞
     2.3.2 Internal lighting: 150W×1
          內部照明：150W×1
     2.3.3 One test platform made of SUS304 stainless steel; sieve type
          Size: W×D =1000mm×1000mm;
         Load: 50kg;
         一個不銹鋼測試平臺，篩網狀，寬1000mm×深1000mm，負載
     2.3.4 Equipped with 4 castors
          4 只萬向腳輪
  2.4 Door: manual single wing door/門：手動單翼門；

     2.4.1 Material: the same as the chamber body;
          材料：與箱體材料一致；
     2.4.2 Opening dimension: W×H=1000mm×1000mm;
          門洞尺寸：寬1000mm×高1000mm
     2.4.3 Window dimension: W680mm×H680mm;
          觀察窗尺寸：寬680mm×H680mm
     2.4.4 Window wiper: to clean the dust on the window; manual
          刮灰器：方便觀察試驗情況，手動
  2.5 Power board: mono-block construction
     電源控制板位置：與箱體形成一個整體
 
3 Dust System/揚塵系統:
 
  3.1 Dust blast fan: Dust blower 3HP with wind speed ≤2m/s;
     揚塵風機：強制對流平衡調溫調濕式；
 
 3.2 Vibrator: Vibrator on the crater type floor to avoid dust attaching to the chamber body;;
     震動器：漏斗型底部安裝震動器避免沙塵附著在箱體表面；
 
 3.3 Dust collecting device: A bypass circulation loop to collect the dust on the chamber floor, and make
     it possible to use dust collector to collect;
     揚塵收集裝置：設置一個專門的旁通回路將沙塵收集在箱體漏斗型底板內，需要的話，可以采用吸塵
     器將沙塵吸出；
  3.4 Dust collector;
     吸塵器；
 
4   Control system/控制系統
 
  4.1 Sampling sensor/傳感器:
     4.1.1 Temperature measurer and sensor: Shielded heat resistance Pt100;
          溫度傳感器：Pt100鉑電阻
     4.1.2 Pressure difference sensor: electronic type;
          差壓傳感器：電子式差壓傳感器測量試件內外差壓
     4.1.3 Glass rotary flow meter to measure evacuating rate;
          玻璃轉子式流量計測量抽空率
  4.2 Controller/控制器:
     4.2.1 Type of controller: 7010;
         
控制器型號：7010
     4.2.2  Language: English;Chinese
           語言：英語，中文
     4.2.3  M-M interface: 7” TFT liquid-crystal colorful displayer;
           M-M界面：7” TFT 液晶彩色顯示器；
     4.2.4  Setting: Touch screen method;
           設置：觸摸面板方式
     4.2.5  Resolution: Temperature: 0.1℃, Time: 1min;
           分辨率：溫度：0.1℃，時間1分鐘
     4.2.6  Setting-range: Temperature: RT+5～+50℃
           設定范圍：溫度：RT+5～+50℃
     4.2.7  User procedure capacity: 999 programmable programs, with maximal 999 steps(segments)
           in each procedure,999 cycle steps, and the procedures is linkable;
           程序容量：999個可編程程序，每個程序*大999 步，可設999 個循環，程序可以鏈接；
     4.2.8  Operation mode: Constant value operation, program operation;
          運行方式：程序方式、定值方式
     4.2.9  Experimental data display: Preset value, measured value, total operation time, segment
          operation time, segment remaining time, heating status;
          試驗數據顯示：預設值，測量值，總運行時間，每一段的運行時間和剩余時間，加熱狀態；
     4.2.10 Failure information: in abnormal case, display the failure status and possible reason;
           故障信息：發生故障時，顯示故障狀態和可能的原因；
     4.2.11 Equipped with USB interface to PC;
           配有USB 接口與計算機連接；
     4.2.12 Automatic selection of cooler’s working status: According to different experimental conditions,
           select the cooler’s working status;
           根據不同的試驗條件自動選擇冷凍機的運行狀態；
     4.2.13 Advanced function: Timing operation, operation record, PID series subarea and PID series
           auto-adjustment, manifold offset, online help;
           高級功能：定時功能，運行數據記錄，PID 分區和自動整定，偏差設定，網上幫助等；
     4.2.14 Recording function: The memory of the controller can record the test curve and data,
           equipment status, alarm record for 6 months and the data can be downloaded by USB;
           記錄功能：控制器的內存能夠自動記錄長達6 個月的測試曲線和數據，設備狀態，報警狀態等，
           并且能夠通過USB下載；
 
5 Security Protection System/安全保護系統:
 
  5.1 The Switch cabinet incorporates the complete electrical section with fuses, protection, switches,
     control, and regulation appliances;
     所有的電氣部分包括保險絲、保護開關、控制器以及相關的調節器件都集成在電氣柜中
  5.2 Lack or reverse of power phase protection/電源斷相及逆相保護
  5.3 Over-temperature protection/過溫保護
  5.4 Overload protection of motor/風機過載保護
  5.5 Overload protection of vacuum pump/真空泵過載保護
  5.6 Fuse for control and lighting/控制回路和照明回路保險絲
 
6 Equipment Working Condition/設備工作條件
 
  6.1 Ambient Environment/環境要求:
     6.1.1 Ambient temperature/環境溫度：+5℃～+35℃;
     6.1.2 Relative humidity/相對濕度：≤80%RH;
  6.2 Power supply/電源要求:
     6.2.1 Power voltage/電壓: AC380±10%V, 3-phase wires + N + G (ground wire protection);
     6.2.2 Frequency/頻率: 50±0.5Hz;
     6.2.3 Max. power/*大功率: 5KW;
     6.2.4 Max. current/*大電流: 10A;
 
7 Applicable Standard: IP5X適用標準：IP5X
 
8 Customer Responsibility/用戶的職責:
  8.1 Floor Foundations – If necessary, provide the foundation according to vendor supplied information;
     土建地基–如果必要的話，根據供應商提供的信息提供土建設計和建造；
  8.2 Main Power Supply Connection – Material & Labor, according to vendor supplied information to
     agreed nominated location;
     主電源連接–提供材料和勞動力，根據供應商提供的信息到的位置；
  8.3 Town Water Connection – If necessary, material & Labor, according to vendor supplied information
     to agreed nominated Demonized location;
     加濕水連接–如果必要的話，提供材料和勞動力，根據供應商提供的信息到的位置；
  8.4 Cooling Water Connection – If necessary, material & Labor, according to vendor supplied
     information to agreed nominated location
     冷卻水連接–如果必要的話，提供材料和勞動力，根據供應商提供的信息到的位置；
  8.5 Drainage – If necessary, provide drainage according to vendor supplied information;
     排水–如果必要的話，根據供應商提供的信息到的位置；
  8.6 Unpacking – Labor to unpack the package;
     拆箱- 拆包裝的勞動力
  8.7 Rigging & Lifting – Provide tools and labor to carry the chamber to required location;
     索具及起重–提供工具和勞動力將試驗室移動到廠內要求的地點。
 
9 After-sale Service/售后服務:
  Charge-free warranty will last for 1 year from the date of equipment acceptance. After the warranty
  period, the user will be charged properly. Irregular examination and life-long service are available;
  設備的無償保修期限為壹年，從設備驗收之日起計算。在保修期外，該設備的維修工作要適當收取費用。
  該設備享有終身維保服務。
 
10 Technical training/培訓:
  Provide charge-free training to 2 operators;
  對兩位操作人員提供無償技術培訓
 
11 Accessories/附件:
  11.1 The certificate of quality: one copy;
      合格證書：1 份
  11.2 Warranty card: one copy;
      質保證書：1 份
  11.3 Instruction Manual: one copy;
      操作手冊：1 份