制造公司(MAKER): 韓國(KOREA)： TECHNOX
型號(MODEL) : TX-80(A-C)
A.產品特征(Features) ;
1. Manufacturing testing equipment based on vacuum insulation for high insulated
performance.使用隔熱性能高的真空保溫材料制造的實驗機器。
2. Over eight times higher insulated performance compare to existing insulation.
比現有的保溫材料高出8倍以上的隔熱性能。
3. Maintaining the stable high precision for temperature and humidity.
對與溫度濕度能維持穩定的高精密度。
4. Reliable testing equipment based on vacuum insulation with environmental friendly and high insulated performance.采用親環境高隔熱性能的真空保溫材料的信賴性試驗機。
5. Average diameter for silica basic particle of vacuum insulation is extremely small with 7~40nm and wide surface area with 50~380m2/g. Highest insulated performance display due to low thermal conductivity with three-dimensional type.
真空隔熱材料的硅石基本粒子的平均直徑為7~40mm，非常小，因為廣泛的表面積 (50~380m2/g)和三元形態的特性，熱傳導率非常低，可以發揮佳的隔熱性能。
6. Vacuum insulation with thermal conductivity of less than 0.0045W/mK Strengthens over eight times insulated performance compare to the same thickness "GA" class insulation.
真空隔熱材料熱傳導率值為0.0045W/mK 以下，具有比同一厚度基準的 “甲”級隔熱材料高出8倍以上的隔熱性能 。
7. Reliable testing equipment based on vacuum insulation can reduce the thickness of insulated wall conspicuously due to maintaining over eight times for insulated performance compare to existing insulation and be more profitable for energy saving and utilization of the space and secure user space.
利用真空隔熱材料的信賴性試驗機器與原有的隔熱材料相比具有8倍以上的隔熱性能，減少隔熱壁體的厚度不僅帶來節能和利用空間的效果，而且還有利于確保使用空間。
B. 產品規格Specification;
1) 試驗箱部件Chamber part)
- 內箱尺寸 Dimensions (in): 400 x 400 x 500 (W*D*H)mm
- 外部尺寸 Dimensions (out): 900 x 900 x 900 (W*D*H)mm
- 內部材料 Material ( in) : SUS 304 1.2T Polished plate
- 外部材料 Material (out) : Cold rolled steel plate with baked coating finish.
- 隔熱材料 Insulations :vacuum insulation for high insulated Prformance(VIP) Poly-urethane foam & glass wool真空隔熱材料(VIP) 聚氨酯 及玻璃纖維 。
- 試驗箱門密封 Door packing : 雙重硅酮密封 Silicon packing
2) 溫度控制系統(Temp. Control system)
- 溫、濕度試驗范圍 Test temp. range : -40℃ ~ 180℃ / 20% ~ 98%RH
-溫濕度控制圖：
- 溫、濕度精密度Temp. & Humid. range : ±0.3℃ / ±1.5%
- 溫、濕度均勻度 Temp. & Humid. Uniformity: ±1.5℃ / ±2%
- 溫度上升比率 Temp. heat up rate : RT ~ 150℃ heating (1-3℃/min)（非線性）約35min
- 溫度下降比率 Temp. Pull down rate : RT ~ -40℃ Cooling (0.7-2℃/min) （非線性）約45min
- 溫度程序控制器 Temp. Program controller :
* Model : TH-500 * Maker: HANYOUNG NUX
* P.I.D 自動調整控制 P.I.D auto tuning control / alarm monitor system
* 99 Pattern / 800step
* 通訊 Communications: RS- 232/485
- 溫度感應器 Temp. & Humid. Sensor : PT100? / Electronic type
- 加熱器 Heater:
* STS pipe fin heater 2.0kW (TEMP)
* STS pipe sheathed heater 2.0kW (HUMID)
3) 循環系統 (Circulation system)
- 強熱風扇 Sirocco fan: 3" x 6" x 4
- 循環電機Circulation motor : 60W x 2SET
4) Freezing System
- 雙冷凍系統 Dual freezing system
- 制冷機 Refrigerant M/C: 1HP x 2SET
- 制冷劑 Refrigerant : R404a & R23
- 冷卻系統 Cooling system: 空氣冷卻 AIR COOLED TYPE
5) 儀表板 Instrument panel
- 溫度程序控制器 Program Temp. controller
- 主電源及箱內燈開關 Main & Lamp S/W
- 記錄器 Recorder
- 透視窗 Viewing window: 400 x 500 x 38T
- 緊急開關Emergency
6) 安全裝置 Safety device
- N.F.B
- 過熱保護器 Over heat protector
- 電機過載繼電器 Motor Over load relay
- 冷凍過載繼電器 Refri. Over load relay
7) 保修 Accessories
- 電纜端口 Cable port: ￠50 x 1ea
- 擱板 Shelves: STS 不銹鋼網式 STS mesh type x 2set
8) 記錄器 Recorder
- 型號 Model: GR-100
- 2 數字點 2 point digital
- 制造公司 Maker : HANYOUNG NUX
9) 電源 Power source: AC 220V/50HZ 3Phase 4.0KW
10) 保證 Warranty
- 免費維修服務In the free repair service
- 提供目錄 The manual offer
D. 其他事項(Remarks) ;
1) Original catalogue and specification are attached.
產品目錄及使用說明書附表。
2) Installation and a test-run should be performed by a qualified engineer.
設置及試運轉由專門領域的進行 。
3) two year warranty should be provided after the installation.
保修期為售后2年
4) Electrical service line contruction work to the installation on-site should
be done by the customer. 客戶負責把電線設置在設備安裝的位置。
5) IN-OUT piping work of water pipe system to the installation on-site should
be done by the customer. 需要供排水設施時，客戶負責把進出水管道設置在設備安裝的位置。
