一、熔體流動速率儀產品簡介：
熔體流動速率儀是按GB/T3682、ISO1133、ASTMD1238的試驗方法測定熱塑性高聚伍在高溫下流動性能的儀器，用于聚乙烯、聚丙烯、ABS樹脂、聚碳酸酯、尼龍氟塑料等高聚物在高溫下熔體流動速率的測定，適用于工廠企業及科研單位的生產和研究之中。
1. Product introduction:
The melt flow rate instrument is an instrument for measuring the flow performance of thermoplastic high polymer at high temperature according to the test methods of GB / T3682, ISO1133, and ASTMD1238. It is used for high polymer such as polyethylene, polypropylene, ABS resin, polycarbonate, nylon fluoroplastic, etc. The measurement of melt flow rate at high temperature is suitable for production and research in factories, enterprises and scientific research units.
二、熔體流動速率儀技術參數：
1、擠壓出料部分：
★出料口直徑：φ2.095±0.005毫米
★出料口長度：8.000±0.025毫米
★裝料筒直徑：φ9.550±0.025毫米
★裝料筒長度：150±0.01毫米
★活塞桿頭直徑：Φ9.475±0.015毫米
★活塞桿頭長度：6.350±0.100毫米
2. Technical parameters:
1. Extrusion part:
★ Outlet diameter: φ2.095 ± 0.005mm
★ Length of outlet: 8.000 ± 0.025mm
★ Charging barrel diameter: φ9.550 ± 0.025mm
★ Charging barrel length: 150 ± 0.01mm
★ Piston rod head diameter: Φ9.475 ± 0.015mm
★ Piston rod head length: 6.350 ± 0.100mm
2、試驗砝碼（相對誤差≤0.5%）
1號 | 0.325kg | 5號 | 4.675kg |
2號 | 0.875kg | 6號 | 5.000kg |
3號 | 0.835kg | 7號 | 2.500kg |
4號 | 3.475kg | 8號 | 2.915kg |
三、熔體流動速率儀工作原理：
熔體流動速率儀是在規定溫度條件下，用高溫加熱爐使被測物達到熔融狀態，這種熔融狀態的被測物，在規定的砝碼負荷重力下通過一定直徑的小孔進行擠出試驗，擠出物的質量折算為10分鐘的擠出量。在工業企業的塑料生產及科研單位的研究中，經常用“熔體（質量流動速率）”來表示高分子材料在熔融狀態下流動性能。
3. Working principle:
The melt flow rate instrument is to use a high temperature heating furnace to make the test object melt under a specified temperature condition. This molten state test object is extruded through a small hole of a certain diameter under a specified weight load gravity In the test, the mass of the extrudate was converted into the extrusion volume of 10 minutes. In the research of plastic production and scientific research units of industrial enterprises, "melt (mass flow rate)" is often used to express the flow properties of polymer materials in the molten state.
四、標準試驗負荷（kg共八級）
★1級：0.325kg=（活塞桿+砝碼托盤+隔熱套+1號砝碼體）=3.187N
★2級：1.200 kg=(0.325+2號0.875砝碼)=11.77 N
★3級：2.160 kg=(0.325+3號1.835砝碼)=21.18 N
★4級：3.800 kg=(0.325+4號3.475砝碼)=37.26 N
★5級：5.000 kg=(0.325+5號4.675砝碼)=49.03 N
★6級：10.000 kg=(0.325+5號4.675砝碼+6號5.000砝碼)=98.07 N
★7級：12.500 kg=(0.325+5號4.675砝碼+6號5.000+7號2.500砝碼)=122.58 N
★8級：21.600 kg=(0.325+2號0.875砝碼+3號1.835+4號3.475+5號4.675+6號5.000+7號2.500+8號2.915砝碼)
★恒溫范圍：30℃---450℃
★恒溫精度：±0.2℃
★電源電壓：220V±10% 50Hz
★工作環境：環境溫度5℃--50℃ 環境相對濕度為30%-80%；周?chē)鸁o(wú)腐蝕性介質，無較強空氣對流；周?chē)鸁o(wú)震動、無較強的磁場器外形尺寸：250X360X514(長X寬X高）
4. Standard test load (eight grades in kg)
★ Level 1: 0.325kg = (piston rod + weight tray + insulation sleeve + 1 weight body) = 3.187N
★ Level 2: 1.200 kg = (0.325 + No. 2 0.875 weight) = 11.77 N
★ Level 3: 2.160 kg = (0.325 + No. 3 weight 1.835) = 21.18 N
★ Level 4: 3.800 kg = (0.325 + No. 4.3.475 weight) = 37.26 N
★ Level 5: 5.000 kg = (0.325 + No.5 weight 4.675) = 49.03 N
★ Level 6: 10.000 kg = (0.325 + No.5 weight 4.675 + No.6 weight 5.000) = 98.07 N
★ Level 7: 12.500 kg = (0.325 + No.5 weight 4.675 + No.6 weight 5.000 + No.7 weight 2.500) = 122.58 N
★ Level 8: 21.600 kg = (0.325 + No. 2 0.875 weight + No. 3 1.835 + No. 4 3.475 + No. 5 4.675 + No. 6 5.000 + No. 7 2.500 + No. 8 2.915 weight)
★ Constant temperature range: 30 ℃ --- 450 ℃
★ Constant temperature accuracy: ± 0.2 ℃
★ Power supply voltage: 220V ± 10% 50Hz
★ Working environment: ambient temperature 5 ℃ --50 ℃, relative humidity 30% -80%; no corrosive medium around, no strong air convection; no vibration around, no strong magnetic field interference.
★ Instrument size: 250X360X514 (length X width X height)
五、注意事項：
★單相電源插座必須有接地線孔，并可靠接地。
★液晶顯示器上若出現異常顯示時，按＂復位”鍵。
★正常工作中，若爐溫大于450℃, 則軟件保護，中斷加熱。
★異常現象發生，如不能控溫，不能顯示等，應關機，進行檢修
★清洗活塞桿時，不能用硬物刮削。
Five, matters needing attention:
★ Single-phase power sockets must have grounding wire holes and be reliably grounded.
★ If an abnormal display appears on the LCD, press the "Reset" button.
★ In normal operation, if the furnace temperature is higher than 450 ℃, the software is protected and the heating is interrupted.
★ Abnormal phenomena, such as temperature control and display failure, should be shut down for maintenance
★ When cleaning the piston rod, do not scrape with hard objects.
